• 2026-05-18

selecting the right material is the core of high-quality precision stamping parts. The proper material directly affects dimensional tolerance, structural stability, service life, surface treatment effect and overall production cost. For electronic terminals, new energy motor accessories, automotive stamped components and custom hardware parts, material selection must match application scenarios. &...

• 2026-05-19

Terminals are core connection components for energy storage batteries, responsible for energy transmission and module connection. Copper is the first choice for energy storage battery terminals, especially customized metal stamping terminals. What makes copper irreplaceable?     As a professional precision metal stamping manufacturer, we summarize the core reasons for copper's wide appli...

• 2026-05-27

5052-O aluminium is one of the most widely used aluminium alloys for exterior parts across architecture, automotive, marine equipment and outdoor enclosure manufacturing. Featuring outstanding corrosion resistance, premium ductility and cost-efficiency, this annealed Al-Mg alloy has become the preferred material for all kinds of outdoor exposed components.   Superior Corrosion Resistance for ...

• 2026-05-30

What Is Salt Spray Test? The salt spray test is an accelerated corrosion test to evaluate the anti-rust and corrosion resistance of metal stamping components, surface coatings and electroplating finishes. It is widely required by overseas buyers for automotive parts, home appliance hardware, electronic terminals and outdoor industrial accessories.   Main Test Standards Our factory follows int...

• 2026-06-01

Minimum Thickness: 0.01mm for Ultra-Thin Foils In industrial practice, the minimum practical thickness is 0.01mm (10μm) for soft, ductile materials like copper, aluminium, or stainless steel foil, using ultra-precision dies and high-speed presses.   Standard precision stamping: 0.1mm–3.0mm (85% of applications fall between 0.3mm–1.2mm).   Ultra-thin specialty stamping: 0.0...

• 2026-06-02

Motor cores including stator and rotor laminations are critical components that determine motor efficiency, stability and service life. Manufacturers classify them into new energy motor cores and traditional motor cores. Though both stator and rotor parts are made of laminated silicon steel via stamping, they differ greatly in materials, precision standards and applicable working conditions.  ...

• 2026-06-03

Grain-Oriented vs Non-Oriented Silicon Steel: Which for EV Motors? Most buyers confuse grain-oriented and non-oriented silicon steel for EV motor production. Here is the clear distinction:   Grain-Oriented Silicon Steel (CRGO): Designed only for single-direction magnetic flux transformers. Not applicable for EV stators and rotors.   Non-Oriented Silicon Steel (NOES): Features uniform mul...

• 2026-06-17

  What is SPCC I/O Backplate? SPCC is a low-carbon cold rolled steel widely used for mass-market computer I/O shields. It offers excellent stamping performance, low material cost and good low-frequency magnetic shielding ability. SPCC is soft and easy to bend, which helps produce precise grounding spring tabs and clean port cut outs for mass production.   The main disadvantage of SPCC is...

• 2026-06-22

Why Terminal Precision Matters for Motors Even tiny flaws in terminals create big problems:   Energy loss: Poor fit increases contact resistance, raising heat and lowering efficiency.   Connection failure: Vibration or thermal cycling causes loose contacts, leading to motor shutdowns.   Safety risks: Overheating from unstable connections can trigger short circuits.   Micro prec...

• 2026-06-23

Precision plays a vital role in hardware stamping parts. You depend on precise manufacturing to ensure high product quality, safety, and reliability. The table below shows how precision shapes these aspects in industrial and medical fields:   Aspect Impact on Product Quality Impact on Safety Impact on Reliability Precision in Stamping Ensures components meet strict quality standards Critical ...

• 2026-06-25

What are the common materials for CPU mounting brackets? Most high-standard CPU brackets are made of cold rolled steel sheet and aluminum alloy through stamping forming. Steel brackets have stronger bearing capacity, not easy to deform, suitable for heavy-duty large heat dissipation fans. Aluminum alloy brackets are light in weight, with anodized anti-rust treatment, good heat conduction and long ...

• 2026-06-29

What Exactly Are Automotive Wire Terminals? Automotive wire terminals are precision stamped metal contacts fixed on wire ends. They build detachable, firm and anti-vibration electrical connections between wires, sensors, ECU modules, batteries and auto accessories.   Different from ordinary electronic connectors, auto wire terminal connectors can resist high temperature, strong vibration, wat...